Pre-Wired Guitar wiring harness | Les Paul 'Short Shaft' kit | Right Handed & Left Handed

£54.99

Delivery time
I usually make harnesses to order, due to the variety of spec options that could be chosen across the range. The waiting time for harness orders is around 3-5 working days depending on quantity of orders in at the time and your order will be updated accordingly when dispatched.

Description
For such a simple configuration, I must admit that the Les Paul harness has been the model I've researched and refined the most in my time making harnesses. I wanted to be respectful of the traditional aspects of the guitar that so many people love, bringing the best out of the iconic Gibson design. After offering a variety of specs over the years, I've now settled on 50s style wiring as standard, with high quality components and a few spec choices which I hope to help the install process that little bit easier. This listing is for the 'Short Shaft' pot version of the kit which I'll touch on shortly.

Installing
I have intended for my wiring harnesses to be as simple as possible to install to your Les Paul, as well as writing in depth fitting guides, how-to instructions documenting the step by step process as well as a simple to follow wiring diagram.
The parts I use, in particular the pots, are US made CTS branded pots which are imperial measurements. If you're fitting this harness to a far east built variant for example such as a Epiphone or similar, then you may have to widen the holes in the body to accommodate for these imperial measurement pots. 
For reference, the CTS pots I use in this harness have a shaft diameter of 9.5mm.
You may also require new control knobs to fit the CTS pot 'split shaft' spline diameter of 5.95mm.
If you do require US spec control knobs, we do carry a selection of popular options in stock and they can be viewed in the hardware & plastic hardware categories on the store.

The mounting board I ship my harnesses out on, were taken from measurements of a USA build Gibson Les Paul. The centre to centre measurements between components are - 
Centre of neck volume pot and neck tone pot - 63mm
Centre of neck volume pot and bridge volume pot - 50mm
Centre of neck tone pot and bridge tone pot - 50mm
Centre of bridge volume pot and bridge tone pot - 61mm

With or without the toggle harness?
This ultimately comes down to your requirements for the work being carried out. If you're happy with the quality or condition of your existing toggle switch and jack, then you can simply order the pots only section of the harness meaning you can use your existing toggle switch and jack. But if you feel the quality or condition of your existing switch or jack isn't up to the job, then I also offer Les Paul harnesses as a complete kit including a new pre wired Switchcraft toggle switch and Pure Tone Multi contact jack socket. High quality components as a complete upgrade/replacement. 

Long or Short, which do I need?
The question I probably get asked most is, "Will I need long or short shaft pots?". Well Gibson are of course known for lots of transitional changes to specs from the golden era right up to modern day. I have compiled a list of Gibson models which use either Short or Long shaft pots on the individual pot listing HERE But, if you're still not sure, the simplest answer is that ALL types of Gibson or Epiphone Les Paul will fit a long shaft pot, as you can adjust the two supplied nuts to suit the height in the body. All Epiphone Les Paul's with exception of the Elitist model use short shaft pots. Also, feel free to send me a photo of the inside of the control cavity or a photo of the pot itself, hopefully I can help identify it for you.

With or without Treble Bleed?
First up, what does it do? A Treble Bleed kit takes the 'high' treble tone frequencies out of the circuit at the volume pot, and puts them back in the circuit as the signal leaves the volume pot. This means the treble frequencies are prevented from naturally bleeding out of the circuit as your turn your volume pot down. The result is a smoothed out treble and a more uniform tone from 1 to 10. Reducing the treble drop out as the volume pot rolls off. Some guitar players wouldn't be without a treble bleed, and many have never used one on their guitars. Truth is, it is very much personal preference. If you like the idea of retaining treble as you roll your volume pot down, then a treble bleed is for you!
To note, treble bleeds aren't really needed for fifties style wiring due to the way fifties wiring works. You can have them on if you like and I have included it as a drop down option as some customers still request them, but just a heads up!


Parts used

- CTS 'TVT' Series +/-10% Tolerance Short Shaft pots - 500k split shaft
- SoZo .022uF Mustard tone capacitors  (If you'd prefer a different value capacitor, do please get in touch and I'd be happy to help, but as standard all of my kits come with .022uF value)
- 20AWG Tinned copper ground
- Soldered using Rapid 22SWG lead-free solder

- For harness kits with the additional toggle section, I use a Switchcraft 3 way short frame toggle switch. (We use this as there is more thread and more space left in switch cavity, makes life a lot easier when mounting!) No need to use an extended knurled nut.
- Pure Tone multi contact jack socket
- Gavitt Braided 22AWG wire
- 20AWG Tinned copper ground
- Soldered using Rapid 22SWG lead-free solder