Pre-Wired Guitar wiring harness | Full Jazzmaster kit | Right Handed

It's no secret that I love Jazzmasters. From the comfort of the offset body shape, to the intuitive vibrato and ultimately, the sound. So this harness was definitely driven by the passion I have for the Jazzmaster design!
Traditional wiring style featured here, but with the choice of a few pot/cap spec changes to suit your preferences/pickup specs etc. Hope this helps!

Pot value options and treble bleed?
Traditionally, vintage (and some new vintage correct models) were supplied with 1MEG Linear taper volume pots in the lead circuit (whilst still having an audio taper pot in the tone position). So if you are looking for that real vintage spec, then I figured this would be a good option to now offer. 

I also offer it with the popular perhaps more modern-spec audio/logarithmic 1MEG lead circuit pots, this is perhaps the most popular choice for modern guitars as audio taper closer represents how the human ear responds to sound, in a logarithmic manner. But one thing I noticed with Jazzmasters is that due to their naturally bright tone, rolling off the 1MEG audio taper volume pot can naturally lose some of the brightness through the taper. So to help with this and retain the chime right through the pot sweep, I also now offer the option of a treble bleed cap too! This will help retain the otherwise 'lost' treble frequencies as the volume rolls down and puts it back into the signal helping maintain that JM chimey/bright character right down the volume pot. But as treble bleed caps aren't for everyone, it's available as an option with or without. I must admit though, 1MEG audio taper pots in a JM seem to really benefit from a treble bleed cap I personally think!

If you have chosen a different set of pickups, like humbuckers or P90s perhaps, or simply want to tame some of the top end brightness associated with Jazzmasters, then I also offer this harness with 500k pots too! These are audio taper only.

It has become a popular choice recently to install much lower value 250k pots in the lead circuit also. I have decided to list it as an option now after some feedback from a good customer whom ordered it with this spec and loved the results. 

I feel that this makes my traditional Jazzmaster wiring kit a great choice as you can choose the pot type and value/spec that suits your preferences, between vintage, modern, alternative pickup and personal tastes.

Cap value options
Similarly to the choices between pots, I also offer the choice of lead circuit tone capacitor value. Traditionally Jazzmasters with 1MEG lead circuit pots were paired with a .033uF tone capacitor. So if you're looking for traditional/vintage style specs, this may well be the choice for you and pairs very well with 1MEG pots. 1965 models featured a .1uF tone cap, expect a more drastic/significant roll off of the top end though the sweep and warmer tone as a result.
But if you are perhaps going for 500k or 250k pots, then you may find a .033uF will soften the top end too much or create a less gradual tone pot sweep, so I also offer a .022uF cap value. Simply put, a .022uF will sound a little brighter than a .033uF cap and is a very popular pairing for 500k pots or 250k pots (as well as a popular choice for humbuckers or P90s for example if your JM has alternative pickup types).

Let's face it, harnesses aren't really the thing to 'demo' on YouTube, but this video recently surfaced of the awesome Chris Buck playing his Jazzmaster which has one of my pre-wired Jazzmaster harnesses fitted and it seemed a shame not to share it here. Chris' harness featured the 'true to vintage' specs throughout, which means in the lead circuit he has the 1MEG linear volume, 1MEG audio tone and .033uF cap options. If that helps at all!
 

I have intended for my wiring harnesses to be as simple as possible to install to your Jazzmaster, as well as writing in depth general fitting guides and simple to follow wiring diagrams for each wiring style. There are also multiple useful how-to guides regarding wiring work found HERE too. But in this section you'll find some important fitting notes that will hopefully help you assess whether the kit is suitable for your exact Jazzmaster or what is required to allow it to fit correctly.

Can I fit this kit myself?
This ultimately comes down to whether you own the equipment needed to correctly and safely install the kit, or how comfortable you feel working on your own guitar. I do feel that installing a pre-wired guitar harness is do-able for many guitarists but only if the correct tools are used and care is taken to ensure you do not damage the kit, your guitar or yourself! There are detailed installation guides here on my website, as well as simple to follow wiring diagrams all to help make the process as easy as possible and in my experience, these have helped thousands of my customers carry out their own install. But if for any reason you have concerns about fitting the kit yourself which is entirely understandable, then I'm sure you'll agree that it is likely best to have a professional fit the kit and help ensure your purchased kit, and your beloved guitar are both looked after and worked on correctly. 
If you are local to me (Stourbridge, West Midlands) I take on guitar work no problem at all so will certainly be able to help install your Signature Series harness. 

Will the pots/jack fit my pickguard and jack plate?
The components I use in my Signature Series wiring kits are for the most part, USA imperial specification, and will be a direct replacement for a genuine USA or Mexico made Fender Jazzmaster. If you're fitting this harness to different model/spec of Jazzmaster, or a far east built guitar such as a Squier or similar brand, then you may have to widen the holes in the pickguard to accommodate for these imperial measurement pots. The CTS pots and Pure Tone multi contact jack have a mounting thread shaft diameter of 0.369" / 9.38mm so I recommend for ease of install a pickguard and/or jackplate with 0.394" / 10mm pot/jack mounting holes. You can easily widen the holes in the Pickguard too if you would prefer, I recommend doing this safely with a step cutter drill bit. I also offer this as a service so if you would like me to widen your plate for you, do please get in touch and we can organise this additionally.

What control knobs will fit?
The kit uses CTS Split shaft pots. Split shaft pots have a adjustable split shaft diameter of 5.95mm w/ 24 splines. You will need control knobs that push-fit and suit these measurements. 
Do not attempt to force fit smaller, metric/import spec control knobs onto the imperial USA spec pots, doing this can damage the pot.

If you do require a US spec control knobs, I do carry a selection of popular options in stock and they can be viewed in the Control Knob category on the store.

The harness does come supplied with the roller wheel control knobs pre fitted on the fuzz controls for you. Those secure to the pot shaft with a grub screw, and you may need to loosen then adjust their precise position and tighten depending on the exact pickguard as they can all ever so slightly differ. 

Which switch tip will fit?
Much like with the control knobs, the Switchcraft pickup selector in this kit is USA spec, with imperial thread sizes. Therefore you need a imperial thread switch toggle tip to suit Switchcraft toggles.

If you do require a US spec switch tip, I do carry a selection of popular options in stock and they can be viewed in the Switch Tips category on the store.

- Choice of lead circuit pot values/specs:
2x CTS 450 Series 1MEG Audio taper (volume and tone)
1x CTS 1MEG Linear taper for Volume (with 1x audio taper for tone)
2x CTS '450' Series 500k audio taper (Volume and tone)
2x CTS '450' Series 250k audio taper (volume and tone
- 1x .022uF or .033uF Mustard tone capacitor in the lead circuit
- 1x .022uF 'Yellow Mustard' type tone capacitor in the rhythm circuit
- 1x Switchcraft right angle 3 way toggle switch
- 1x Switchcraft 2 position DPDT slide switch
- 1x Right angle rhythm circuit mounting bracket
- 2x Roller wheel control knobs for ryhytm circuit
- 1x Alpha 1MEG Lin mini pot
- 1x Alpha 50k Lin mini pot
- 1x Pure Tone multi contact jack socket
- Gavitt USA made cloth covered 22AWG wire
- 20AWG Tinned copper ground
- Soldered using R-Tech Premium Lead-Free (Sn95.5Ag3.9Cu0.6) 22swg Solder wire 
RoHS Compliant

RoHS Compliant components are used throughout pre-wired assemblies. All components used in this assembly are being used for their intended purposes stated in the guidelines by their relevant manufacturer. Any use outside of stated or recommended guidelines is entirely up to the customer, but sales support/warranty/refunds are then extinguished. For a run down of the manufacturers and product data sheets you can click HERE

Please note - wiring kit does not include new lead circuit control knobs/switch tip etc but does include the switch/pot/jack mounting nuts, washers & screws and does include the rhythm circuit roller wheels. Please see above spec/item list for full detailed run down of what is included or drop me a message if you aren't 100% sure.

Why these spec parts over others available?
Simply put, component choice has been one of the most important parts of my product development. I have worked on guitars for many years, and built these kits professionally since 2015, and as a result have been able to see and experience working on the majority of components available on the market. In my findings, A/B testing and more, I have found the components I decided on for my Signature Series to be the most reliable, best tolerance and great functioning parts to use to help customers get the most out of their instruments. I use CTS '450' series premium spec pots as they have a tight tolerance, and will consistently provide me with accurate value, as well as very solid build quality. I use trusty 'Mustard' style polyester film 'tone' capacitors as in my opinion they simply can't be beat for great value, solid construction, solid lead-outs, super tight tolerances and reliable tone/function. I would personally much rather use a trusty Mustard for example over something like a paper in oil, as from experience that are so much more reliable to use. This is from carrying out a lot of A/B testing, both tonally, as well as armed with the multi-meter for testing values and actual tolerances, as well as handling them to test construction quality for long lasting reliability in use. I use the brilliant 'Pure Tone' Multi Contact Jack sockets as they are incredibly reliable, due to their additional contact points for both tip and sleeve. I use CRL, Oak and Switchcraft brand switches across the range as these are built very well, with care will last for many years to come and have long since provided me with reliable use professionally. All kits are wired up with quality USA made Gavitt wire, it's great to work with, super consistent gauge and provides me with a very reliable quality item for my kits. I totally understand that with anything guitar, it is subjective, but I have, with an open mind, thoroughly tested a broad variety of components over the years and these have all become the items I trust to use every day. 

I've been proudly making, developing and installing my pre-wired guitar harnesses since the beginning of the Home of Tone back in 2015 (time flies when you're having fun right!). Although I feel I do my best in covering as much information as possible across the various product listings, fitting guides, wiring diagrams and more, I thought it might be helpful to put together an FAQ's page that covers some of the general additional questions I get asked. You can view these Harness FAQ's HERE

Looking forward to installing your new wiring, but a little worried about making the ground connections to the pot casings? First time soldering and hear the horror stories of frying pots, or just simply want to neaten up your installs? Then the awesome 'Ground Bug' will help with any of these concerns, beginner or pro modders alike. The Ground Bug is a pot washer that fits between the pot casing and the pickguard/body and has a number of lugs (much like with the main signal connections on the pot for example) to which you can very easily solder your ground wire connections too. Completely removing the worry and risk of soldering a pot casing, something I know many guitarists complain about having to learn to do. 
I have been stocking Ground Bugs for a while, and they really are the perfect match for a pre-wired harness as they further help you with your installs. So I have set up a 10% off Ground Bug deals when purchased with a Home of Tone Signature Series pre-wired harness. This is an automatic discount code, so all you need to have is a Signature Series kit, and a Ground bug in your cart, and the discount will automatically be applied to the bug for you! Click HERE to view the Ground Bug listing

I'm afraid I do not offer a custom harness service. Only kits developed, tested and listed on my website are the available kits. So no custom schematics etc. If you happen to be local to my office, then I do carry out custom work in house, but in regards to shipped out pre-wired harnesses I do not offer custom kits. I am however happy to use different pot values or cap values within reason if you have a specific requirement that differs to the specs listed above. If this is relevant to yourself then please get in touch to discuss further to ensure the request is possible.