Pre-Wired Guitar wiring harness | 4-way Telecaster Thinline kit | Right Handed


Order times
I usually make harnesses to order, due to the variety of spec options that could be chosen across the whole range. The current turnaround time for a harness orders is around 5-7 working days depending on quantity of orders in at the time and your order will be updated accordingly when it is dispatched. This turnaround time doesn't include the transit time. Thanks for your patience whilst I get your harness made!

The Telecaster is an iconic instrument, that defined a brand, inspired so many musicians and set the bar for the electric guitar moving forward. I want my Signature Series wiring harness for this legendary guitar to earn the right to be a small part of that through a choice of quality components and respect for it's design. This schematic is the super popular 4-way mod, retaining the traditional 3 position Telecaster sounds but with an additional position putting the two single coils in series for a chunkier sound, and the parts aim to bring out the best in your telecaster's tone, and aim to do so for many years to come. 

I have intended for my wiring harnesses to be as simple as possible to install to your Telecaster Thinline, as well as writing in depth fitting guides, how-to instructions documenting the step by step process as well as a simple to follow wiring diagram.
The parts I use, in particular the pots, are CTS branded pots which are imperial measurements. If you're fitting this harness to a far east built variant for example such as a Squier or similar, then you may have to widen the holes in the pickguard to accommodate for these imperial measurement pots. 
For reference, the CTS pots I use in this harness have a shaft diameter of 9.5mm.
You may also require new control knobs to fit the CTS pot 'solid shaft' diameter of 6.35mm.
If you do require a US spec control plate or control knobs, we do carry a selection of popular options in stock and they can be viewed in the hardware & plastic hardware categories on the store.

Centre to centre measurements between components are - 
Centre of Switch to volume pot - 40mm
Centre of volume pot to centre of tone pot - 40mm
Centre of volume to jack socket - 100mm (but some give in the wire length is allowed for)
These measurements for my templates were taken from a USA Fender telecaster thinline pickguard.


Fitting a 4 way telecaster harness is a little different to a conventional 3 way harness, in that the neck pickup could need modifying depending on how it has been made by the pickup manufacturer. If it is a standard, two wire pickip, it requires an additional ground wire adding which allows for the series position and the small ‘jumper’ wire snipping/removing. I have written a guide to do this HERE but if you are at all unsure about doing this, I would highly recommend supporting your local trusted Tech to carry out the modification for you. This is also shown on the wiring diagram to follow, but please keep this in mind, correct grounding is essential for this schematic to work as it should.

I have also written a blog article, detailing the steps taken when installing a 4 way wiring harness! That can be read HERE

Also, the 4 way switch has a slightly increased throw angle, sometimes requiring a wider slot control plate. Not all control plates can accommodate for a 4 way switch without minor modification. Some players file a very small amount off the slot in the plate, and some players prefer to file a little notch in the 4 way lever. But it is worth baring this in mind, the 4 way mod may require extra attention as noted here. 

Parts used
- CTS '450' Series +/-10% Tolerance pots - 250k, solid shaft pots as standard on Tele thinline kits to suit their single coil pickups.
- .022uF 'Yellow Mustard' type tone capacitor  (If you'd prefer a different value capacitor, do please get in touch and I'd be more than happy to help, but as standard all of my kits come with .022uF value)
- Gavitt USA made cloth covered 22AWG wire
- 20AWG Tinned copper ground
- Oak 4-way Switch
- Pure Tone multi contact jack socket
- Soldered using Rapid 22SWG lead-free solder

Unfortunately, due to the tight proximity of the components in the cavity, I have decided to offer this harness without the option of a treble bleed cap. It would make it difficult to make any ground solder connections and makes things tight to work on. So it is only available without a treble bleed mod I'm afraid. It's also not available as a solderless version for the same, tight proximity of components reason.